DE KEYZER, Jozefien

Email Alert RSS Feed

Profile

Full Name
DE KEYZER, Jozefien
Email
jozefien.dekeyzer@uhasselt.be
 
Loading... 5 0 5 0 false
Loading... 6 0 5 0 false

Publications

Results 1-15 of 15 (Search time: 0.003 seconds).

Issue DateTitleContributor(s)TypeCat.
12020Effect of co‐agents on adhesion between peroxide cured ethylene–propylene–diene monomer and thermoplastics in two‐component injection moldingLAING, Brittany; DE KEYZER, Jozefien; Seveno, David; VAN BAEL, AlbertJournal ContributionA1
22020Quality assessment of mixed plastic flakes from Waste Electrical and Electronic Equipment (WEEE) by spectroscopic techniquesWAGNER, Florian; Peeters, Jef R.; Ramon, Hans; DE KEYZER, Jozefien; Duflou, Joost R.; Dewulf, WimJournal ContributionA1
32020Adhesion between ethylene‐propylene‐diene monomer and thermoplastics in two‐component injection molding: Effect of dicumylperoxide as curing agentLAING, Brittany; DE KEYZER, Jozefien; Seveno, David; VAN BAEL, AlbertJournal ContributionA1
42019Experimental analysis of conformal cooling in SLM produced injection moulds: Effects on process and product qualityEVENS, Tim; Six, W.; DE KEYZER, Jozefien; Desplentere, F.; VAN BAEL, AlbertProceedings PaperC1
52019Two-component injection moulding of thermoplastics with thermoset rubbers: The effect of the mould temperature distributionBEX, Gert-Jan; Six, W.; DE KEYZER, Jozefien; Desplentere, F.; VAN BAEL, AlbertProceedings PaperC1
62019The Influence of Mechanical Recycling on Properties in Injection Molding of Fiber-Reinforced PolypropyleneEVENS, Tim; BEX, Gert-Jan; Yigit, M.; DE KEYZER, Jozefien; Desplentere, F.; VAN BAEL, AlbertJournal ContributionA1
72019Prediction of interfacial strength of HDPE overmolded with EPDMSix, Wim; BEX, Gert-Jan; VAN BAEL, Albert; DE KEYZER, Jozefien; Desplentere, FrederikJournal ContributionA1
82019A novel method for the prediction of adhesive strength for two-component injection molding of thermoplastics with thermoset rubbersSix, W.; BEX, Gert-Jan; DE KEYZER, Jozefien; Desplentere, F.; VAN BAEL, AlbertProceedings PaperC1
92019Towards a more circular economy for WEEE plastics – Part A: Development of innovative recycling strategiesWAGNER, Florian; DE KEYZER, Jozefien; Peeters, J.R.; Janssens, K.; Duflou, J.R.; DEWULF, W.Journal ContributionA1
102019Towards a more circular economy for WEEE plastics – Part B: Assessment of the technical feasibility of recycling strategiesWAGNER, Florian; Peeters, J.R.; DE KEYZER, Jozefien; Janssens, K.; Duflou, J.R.; Dewulf, W.Journal ContributionA1
112018Evaluation of the quality of postconsumer plastics obtained from disassembly-based recycling strategiesWagner, F.; Peeters, J.; DE KEYZER, Jozefien; Duflou, J.; Dewulf, W.Journal ContributionA1
122018Effect of process parameters on the adhesion strength in two-component injection molding of thermoset rubbers and thermoplasticsBEX, Gert-Jan; Six, Wim; LAING, Brittany; DE KEYZER, Jozefien; Desplentere, Frederik; VAN BAEL, AlbertJournal ContributionA1
132018Wetting measurements as a tool to predict the thermoplastic/thermoset rubber compatibility in two-component injection moldingBEX, Gert-Jan; Seveno, David; DE KEYZER, Jozefien; Desplentere, Frederik; VAN BAEL, AlbertJournal ContributionA1
142017Two-component injection moulding of thermoset rubber in combination with thermoplastics by thermally separated mould cavities and rapid heat cyclingBEX, Gert-Jan; Desplentere, Frederik; DE KEYZER, Jozefien; VAN BAEL, AlbertJournal ContributionA1
152017Two-Component Injection Moulding of Thermoplastics with Thermoset Rubbers: Process DevelopmentBEX, Gert-Jan; DE KEYZER, Jozefien; Desplentere, Frederik; VAN BAEL, AlbertProceedings PaperC1